Picture
Caption: BOOKCASE IRONBOUND DIY
Picture
Caption: This DIY bookshelf project
has a nice rustic, modern look
and is easily created from
angle irons and 2x10s.
Picture
Caption: Supplies Two 2x10 (8' long)
Available at Home Depot
36" Long 1 1/2" Square Fir Balusters
Available at Home Depot
1 1/2" Angle Irons (36" long)
Available at the Home Depot
Caption: Tools This project can be made
with hand tools...
RYOBI 18 Volt Cordless Drill
Available at Home Depot
RYOBI 18 Volt Circular Saw (with Plywood Blade)
Available at Home Depot
...but is easier with bench top tools:
RYOBI 10" Sliding Compound Miter Saw with Laser
Available at Home Depot
RYOBI 10" Drill Press with Exactline™ Laser System
Available at Home Depot
Picture
Caption: Lay Out the Design + Mark the Hole Locations You can make this piece with either
3 or 4 shelves. I chose to do a 4 shelf layout, 4 feet long. Mark the desired locations for your shelves and place an
X to mark the place where you
will drill through the steel.
Picture
Caption: Drill Through the Steel Drilling steel is a little different than wood. Make sure you are using drill bits that are meant for steel and check your drill for the appropriate speed settings. Firmly clamp and secure your steel to a work surface when drilling.
Picture
Caption: A lubricating oil should also be used. I didn't have any on-hand, so I used WD40, which was not ideal, but
better than nothing.
Picture
Caption: Drill a single hole that will align with
the center of each 2x10 shelf on the
front facing sides of the angle irons.
Drill 2 holes on the other side for nails that will go into the end of the 2x10
and the sides of the baluster supports.
Picture
Picture
Caption: Trim the 2x10s It's critical that the 2x10 shelves are the same length. I used a benchtop chop saw to make nice accurate square cuts. You can do this with a hand held circular saw, but I would recommend using a speed square clamped on as a guide to ensure the cuts are square.
Picture
Caption: Cut the Balusters into Supports Cut the fir balusters into supports with a length equal to the width of the 2x10s.
Picture
Caption: Sand the 2x10s Use an orbital sander to sand the 2x10s and supports with 220 grit sandpaper.
Picture
Caption: Screw the Supports onto the Shelves Use 2" screws to screw the supports to the underside of the shelves.
Picture
Caption: Round the Corners of the Shelves The inside corners of an angle iron are not perfectly square and have a bit of a radius. Sand the corner edges of the shelves so that they fit nicely into the angle irons.
Picture
Caption: Nail the Back Angle Irons to the Shelves Lay out the back angle irons on the floor and place the shelves in their appropriate locations. Starting from the bottom shelf, start nailing in one nail through the sides of the angle irons and into the ends of the shelves. Make sure the top shelf is flush with the top of the angle irons.
Picture
Caption: Nail on the
Front Angle Irons Place the front angle irons on the shelves. Start with the bottom shelf, making sure it's properly aligned and then drive nails through the angle irons and into the wood. Next, align the top shelf and fasten it with nails. You may need to use a clamp or a second set of hands to wrestle the wood into to place. Nail the other 2 shelves and then stand the whole thing up.
Picture
Caption: Drive Nails Through the Remaining Holes + Rub a Coat of Danish Oil into the Wood to Finish
Picture
Picture
Picture
Picture
Caption: Disclaimer: 2x10s are affordable and look great, but can be a bit warped. This set of shelves is sturdy and functional but not perfectly square.
Caption: Good luck and please email or tweet
photos to @benuyeda or
about@homemade-modern.com
--------------
www.homemade-modern.com